Garment craft の knitwear weaving process summary, worth forwarding collection ~

1, Yuan Tong

Yuantong refers to the weaving method of the beveled knife when the front and back needle beds are involved in the editor's knitting. In order to facilitate the combing, usually the last half of the yuan is less relaxed.

2, over combing

Over-combing refers to the process of transferring a yarn from a needle in a needle bed to a needle on another needle bed using a curved needle plate.

After weaving the Yuantong, firstly, the knitting needles containing the yarn on the front needle bed are lifted up, so that the needles are all opened, and the yarn is transferred to the curved needle board by the curved needle board, and then transferred to the other needle bed. On the needle.

3, unilateral

Unilateral means that there is only one bed of dense needles, the two knives behind the machine head are picked up, only the front needle bed is involved in the weaving weave, the woven piece is lifted, and the woven piece is knotted. Some, the shirt is shorter, and the shirt is longer.

4, pit bars

The crater is also called the rib, which is the basic organization of the double-sided woven fabric. It is composed of the front line wales and the reverse line wales in a certain combination of 6 W* _- ~- O8 c, usually the pits can be divided. For regular pits and irregularities. The ruled crater means that the number of pits on the bottom surface is the same, for example: 1×1, 2×2, 4×4 pits, and the irregular pits mean that the number of pits on the bottom surface is different, for example: 4×2, 3× 6,12 × 3 pits.

There are two different preconditions in the pinning method of the pit strip. One is the pointer to the needle, the other is for the tooth, and the other is a kind of pit weave. The 2 × 2 pit is an example:

A. Under the premise of the needle, the needle-discharging method is two needles with two needles on the bottom.

B. Under the premise of the tooth, the needle-discharging method is to empty the needle with two needles on the bottom surface.

In the usual case, it is mainly based on the situation of the teeth.

5, repair flowers;

The repairing of the flower refers to the addition and subtraction of the sweater during the weaving process. Since the sweater is directly woven into the shirt without cutting, it must be achieved by adding and subtracting the needle. The reduction of the needle refers to moving the two yarns inward. Needle, after the weaving, the woven needle is pressed out and exited. The adding needle refers to the method of lifting up the needles on both sides during the weaving process. By reducing the needle, the width of the cloth piece can be gradually reduced, and vice versa. The width of the cloth piece can be gradually increased. For example, 2-1-5 means that each needle is reduced by one stitch on each side, so that the stitching can be divided into repairing the edgeless flower and trimming the flower. Repairing the borderless flower means reducing a few needles with a few shackles. After the flowering, the smudges are visible on the edge of the cloth. The edging is the stipulation that the needles are pinned when the needle is reduced. The number plus the number of clips. For example, it is required to clip three sides, and one needle is used to reduce five needles. After the flower is repaired, it can be seen that the flowering position is at the fourth needle position on the edge of the cloth sheet.

6, moving the needle

Needle removal means that the needle reduction process cannot be completed at one time. For example, if you need to reduce the needle in the middle of the cloth, you need to move the yarn on the adjacent needle on the outside. One stitch and repeat the process until the edge of the cloth The empty needle is withdrawn, and this process is called moving the needle.

7, Sanping and Siping

In the case where the front and rear needle beds are densely needled, the weaving method of hitting the left three knives and hitting the other three knives is called Sanping, and the weaving method of the four knives is called Siping.

8, the driver

The sergeant refers to the weaving method of the unilateral side of the front and rear needle beds, that is, the weaving method of unilaterally weaving all the yarns to the back needle bed after weaving several unilateral sides of the front needle bed.

9, moving

Removal refers to the formation of a corner weaving method by knit knitting. For example, the back needle bed is dense, the needle front needle is used to lift the four needles, and the four needles are bounded from the middle to the two sides. After the original needle is pressed down, the flower is moved several times to reach the prescribed width, and then the needle is moved inwardly until the four needles are re-synthesized so as to form an angle.

10, provocation and needle

Provocation refers to the weaving process in which the yarn of a needle is moved to the side of the needle to form a weave.

Needle refers to a weave that allows certain needles to exit the knitting process during the weaving process, usually for marking purposes.

11, wicker, twisted rope, valley wave, playing chicken, pearl land

Wicker refers to the pair of diagonal code cutters, one pair is lowered, the other pair is on top, and the needle beds on both sides are involved in the knitting needles (the needle can be 1×1, dense needle, 2×2, etc.) The weave of the request.

A twisted rope is a weave in which yarns on adjacent knitting needles are exchanged at regular intervals during the knitting process.

Gu Bo refers to the weaving method of several special planes with the same face or the same element.

Playing chicken refers to the weaving method of the two-needle bed, the same level and the semi-special (the two knives that the weaving yuan does not participate in the weaving).

The bead is a weaving method in which the three characters are lowered in the case of a fine needle or 1×1 and the other word is raised by 70%.

12, two or three levels of flowers

Usually three kinds of needles (high-legged long tongue, high-legged, low-footed) are used, but depending on the need, one or more of them can be lifted by Zhongshan, and one or more semi-specialized flowers and woven four flats, so spaced. The weaving method is a two-level flowering; when the nose is raised up and down in Zhongshan, weaving a special or semi-specialized flower and then weaving, such a weaving method is called a three-level flowering.

13, mane

The bristles refer to the use of special yarn feeders to guide two different kinds of wool from different positions of the yarn feeder into the weaving process, so that the effect of woven the shirt is that one wool cover is on the other wool, and the bottom surface is different in wool. Weave.

14, fierce flowers

The fierce flower, also known as the Mambo, refers to a weave that uses a hand-made control to move the needle bed during the weaving process to cause the woven piece to have a regular twill.